Introduction
Riacetech Srl. is an Italian manufacturer specialising in wax injection systems and extruded wax consumables for the jewellery casting industry. Their equipment is built around a single discipline — producing accurate, consistent wax patterns that cast cleanly, first time, every time.
In lost-wax casting, the quality of the finished piece is determined well before the metal is poured. It is determined at the wax injection stage. A wax pattern that is dimensionally inaccurate, has surface defects, or traps air will produce a casting with exactly those problems — no amount of finishing work corrects a fundamentally flawed wax. Riace Wax machines are engineered to eliminate these problems at the source, giving casting facilities the pattern quality and production consistency their output depends on.
NJTPL has been supplying Riace Wax systems and consumables to Indian jewellery manufacturers and casting facilities — providing genuine product access, technical guidance, and local support from Mumbai.
Riacetech Srl. Riace Wax
Why Wax Injection Quality Determines Casting Quality
Lost-wax casting begins with wax — and the casting is only ever as good as the wax pattern it starts from. Every dimensional error, surface defect, or air inclusion in the wax pattern carries through into the metal. This is why the wax injection stage, often treated as routine, is actually one of the most consequential steps in the entire jewellery manufacturing process.
Common problems with poor wax injection equipment or technique — incomplete fills, surface shrinkage, distorted patterns, flash at parting lines — translate directly into casting scrap, rework, and metal loss. At production scale, these problems compound quickly.
Riace Wax systems are engineered to eliminate these failure points. Precision-controlled injection gives you:
- Complete, void-free wax fills — patterns that fill every detail of the rubber mould cleanly
- Dimensionally consistent patterns across every injection — critical for production runs of repeat designs
- Controlled injection pressure and temperature — reducing wax distortion, surface shrinkage, and flash
- Faster cycle times compared to manual or basic injection equipment — improving production throughput
- Reduced wax waste through controlled delivery and consistent shot weight
- Pattern surface quality that reduces metal finishing time after casting
For Indian jewellery manufacturers and casting facilities working with rubber moulds across gold, silver, and platinum casting applications, the right Riace Wax system means fewer rejected castings, less metal loss, and better output consistency at every production scale.
Product Range
Mono Vision Touch
The Mono Vision Touch is Riace Wax’s single-station wax injector — designed for precision wax injection with intuitive touchscreen control. Suited to jewellery manufacturers and casting units that require accurate, controllable wax injection without high-volume automation, it delivers consistent pattern quality with straightforward operation. The touch interface gives the operator clear control over injection pressure, wax temperature, and cycle parameters.
Intuitive BI
The Intuitive BI is a dual-station wax injector engineered for higher production throughput — allowing one mould to be injected while the previous pattern is cooling and removed. This overlap in the injection cycle significantly increases the number of patterns produced per shift without compromising on injection control or pattern quality. Designed for casting facilities running production volumes where a single-station injector creates a bottleneck.
Intuitive BI Belt System
The Intuitive BI Belt System takes the dual-station Intuitive BI platform and integrates an automated belt conveying system — moving injected moulds through a controlled cooling zone before pattern removal. This automation removes the operator wait time from the cooling stage entirely, further increasing production throughput and delivering a fully controlled, repeatable injection-to-demould cycle. The right choice for high-volume casting operations where production efficiency and pattern consistency are both critical.
Extruded Wax
Riace Wax extruded wax is a consumable product used for wax model preparation, pattern repair, and hand assembly of wax trees prior to investing. Available in a range of profiles, colours, and hardness grades, Riace extruded wax is formulated to bond cleanly with injected wax patterns and burn out completely during the casting cycle — leaving no residue that could cause porosity or surface defects in the finished casting.
Why Indian Jewellers & Casting Facilities Choose Riace Wax Through NJTPL
Pattern quality that carries through into the casting
Riace Wax systems deliver consistent, void-free wax patterns with clean surface detail — which means castings that require less remedial finishing and produce less scrap.
Scalable across production sizes
Whether you are running a small casting unit with a single injector or a high-volume facility needing automated throughput, Riace Wax has a system at the right scale — from the Mono Vision Touch to the fully automated Intuitive BI Belt System.
Precision control over injection parameters
Riace Wax machines give the operator direct, consistent control over injection pressure and wax temperature — the two variables that most affect pattern quality. This control is especially important when working with detailed rubber moulds for fine jewellery.
Extruded wax that performs in the burnout
Riace extruded wax is formulated specifically for jewellery casting applications — it bonds well, works cleanly, and burns out completely without leaving ash or residue that compromises the casting.
NJTPL's 23 years in Indian jewellery manufacturing
means our team understands which Riace Wax system suits which casting operation, production volume, and mould type — and can help you select and evaluate the right equipment before committing to a purchase.
Frequently Asked Questions
What is the difference between the Mono Vision Touch, the Intuitive BI, and the Intuitive BI Belt System — and how do I choose?
The Mono Vision Touch is a single-station injector suited to operations where precision matters more than volume. The Intuitive BI adds a second station to increase throughput — one mould injects while the other cools. The Intuitive BI Belt System automates the cooling and demould stage entirely, maximising throughput for high-volume casting operations. NJTPL can help you assess which system is right for your current production volume and growth plans.
Are Riace Wax injectors suitable for detailed fine jewellery moulds as well as production casting?
Yes. Riace Wax systems give precise control over injection pressure and temperature, which is essential for filling detailed rubber moulds cleanly without distorting fine features. The same control that makes them suitable for fine jewellery also makes them reliable for production casting — the parameters are simply set differently for different mould types.
What wax types are compatible with Riace Wax injection machines?
Riace Wax machines are compatible with standard jewellery injection waxes across a range of hardness grades and melting points. NJTPL can advise on compatible wax grades for your specific mould types and casting alloys.
What is Riace extruded wax used for beyond tree assembly?
Riace extruded wax is also used for repairing defective wax patterns, adding sprues and gates to patterns, and hand-building wax models. The range of profiles and hardness grades available makes it a versatile bench consumable for any casting operation.
How does automated wax injection with the BI Belt System improve casting yield?
removing operator variability from the cooling and demould stage, the Belt System ensures every pattern goes through the same controlled cooling cycle before removal. This reduces pattern distortion from premature demoulding — one of the more common causes of dimensional inconsistency in wax patterns — which directly improves casting yield.
Where can I buy Riace Wax systems and consumables in India?
NJTPL is the authorised Indian distributor for Riacetech Srl. – Riace Wax products. Contact us at +91 9821318963 or info@njtpl.co.in for pricing, availability, and technical consultation.
Ready to Improve Your Wax Room Output?
Whether you are a casting facility looking to reduce pattern defects and casting scrap, or a growing manufacturer looking to scale wax injection capacity, Riace Wax has the right system for your operation — and NJTPL has the stock, the knowledge, and the support to back it up.